Skip to content
Fuel Comparison

Renewable Diesel vs. Biodiesel: HVO vs. FAME, Side by Side

Same fats and oils, two different fuels. Renewable diesel is diesel by spec and runs neat. Biodiesel is an ester that gets blended. That one difference drives engine approvals, cold weather, storage and supply.

D975Renewable diesel spec
B5Max biodiesel in D975
70–85RD cetane (DOE)
−4% / −7%Energy, RD / B100
R99 delivered nationwide
On-road B0, B5 or B10
20–4,400 gal per drop
800-720-4546
Quick Answer

Renewable diesel (HVO) is fats and oils hydrotreated into hydrocarbons that meet ASTM D975, so R99 and R100 run as drop-in diesel at any ratio. Biodiesel (FAME) is made by transesterification, meets ASTM D6751 as B100 and is sold in blends: up to B5 counts as diesel; B6–B20 falls under D7467. Engine limits follow the blend.

Overhead view of a row of white semi-truck tractors parked side by side in a fleet yard
In a mixed fleet, the engine with the lowest biodiesel approval sets the blend for a shared tank. Renewable diesel doesn't have that ceiling.
Side by side

Renewable diesel vs biodiesel at a glance

Both fuels start from the same feedstocks: soybean and canola oil, used cooking oil, animal fats, distillers corn oil. Everything after the feedstock is different. This table is the short version; each row is explained below.

Renewable diesel (HVO, R99/R100)Biodiesel (FAME, B5–B100)
ProcessHydrotreating: oils react with hydrogen over a catalystTransesterification: oils react with methanol
ChemistryHydrocarbons (paraffins), C8–C25, like petroleum dieselMethyl esters of C12–C22 fatty acids; contains oxygen
SpecASTM D975, any ratio. EN 15940 in EuropeB100: D6751. Up to B5: D975. B6–B20: D7467
How it's soldNeat (R100), R99, or blended with dieselBlended; B5 and B20 are the most common
Engine approvalsOften up to 100% (Detroit, Deere Tier 4, 2027 Volvo D13)Usually capped at B5, B7 or B20 by engine
Cetane (DOE)70–8545–65 (diesel: 40–55)
Energy vs ULSD (DOE)About 4% less per gallonB100 about 7% less; B20 about 1.4% less
Cold flowSet by grade; additives help only a littleB20 clouds 2–7°F above its #2 base
StorageNo use-before date (Neste); picks up less water than dieselAges faster; B20 up to a year clean and dry (NREL); absorbs more water
LubricityNeeds a lubricity additive, like ULSDAdds lubricity; 2% is usually enough
Lifecycle carbon65% lower on average (DOE, California certified values)B100 74% lower (Argonne); a blend carries its share only
Where it's usedMostly California, Oregon, WashingtonNationwide in low blends; most plants in the Midwest

Sources: DOE Alternative Fuels Data Center (fuel properties, renewable diesel, biodiesel emissions), EIA, NREL Biodiesel Handling and Use Guide, Neste Renewable Diesel Handbook, Clean Fuels Alliance America. Engine makers' documents are listed in the approvals table.

Process

How each one is made: hydrotreating vs. transesterification

Biodiesel is made by reacting oil or fat with methanol. The result is fatty acid methyl esters, or FAME, plus glycerin as a byproduct. The esters keep the oxygen that was in the oil. That oxygen is why biodiesel behaves differently from diesel in the cold and in storage. The full biodiesel basics, including what B5, B10 and B20 mean, are in biodiesel vs. diesel.

Renewable diesel is made by hydrotreating, a process taken from oil refining. Neste's handbook describes it: hydrogen strips the oxygen out of the oil molecules and splits each one into three chains, leaving hydrocarbons similar to existing diesel components. NREL says the process produces compounds identical to some of those in conventional diesel. In Europe it's called HVO, hydrotreated vegetable oil. R99 is about 99% renewable diesel; R100 is neat. The names are covered on our R99 renewable diesel page.

The processes cost energy differently. In a 2022 Argonne National Laboratory study, transesterification used less energy than hydroprocessing, and hydrogen accounted for 73% of hydroprocessing's greenhouse gas emissions. Renewable diesel plants are also much larger: EIA notes refiners can convert existing units and that the bigger plants benefit from economies of scale.

Neither one is straight vegetable oil

Raw or refined oils and fryer grease that haven't been processed into biodiesel or renewable diesel are not fuel. NREL says they can cause engine deposits, ring sticking and lube oil gelling at concentrations as low as 1%.

Specs

Specs and blend limits: D975, D6751 and D7467

This is where "drop-in" comes from. Renewable diesel meets ASTM D975, the U.S. diesel spec, so it is diesel on paper at any blend level. EIA says it can be sold with or without petroleum diesel and moved in petroleum pipelines. Biodiesel has its own specs, and the finished fuel changes spec as the blend goes up:

FuelSpecWhat it means on site
R99 / R100ASTM D975Treated as diesel. Blends with petroleum diesel in any ratio. In Europe, EN 15940 (paraffinic diesel), because its density is below the EN 590 minimum.
Up to B5ASTM D975Treated as conventional diesel. The biodiesel share doesn't have to be listed, so ordinary diesel may already be up to B5.
B6–B20ASTM D7467A separate blend spec with added oxidation stability and acid number limits. Needs engine approval above B5.
B21–B99No finished-fuel specNREL says these may need special handling, heaters or different seal materials.
B100ASTM D6751A blendstock. Gels at much warmer temperatures and can attack some hoses and seals.

Sources: EIA Biofuels explained; DOE AFDC, Renewable diesel; NREL Biodiesel Handling and Use Guide (6th ed.). Biodiesel blend details are in biodiesel vs. diesel.

Mixing the two. Renewable diesel blends with petroleum diesel freely, but not with a lot of biodiesel. Neste's handbook says it is not recommended to store renewable diesel with more than 7% FAME: renewable diesel is a poor solvent, and impurities in the biodiesel can precipitate and plug filters, even above the blend's cloud point. EN 15940 itself allows up to 7% FAME. If a tank held B20, draw it down or polish it before the first R99 load.

Engine approvals

Drop-in vs. blend limits: what the engine makers approve

On paper, a D975 fuel goes into any diesel engine. In practice, fleets go by the engine maker's fuel bulletin, and that's where the two fuels split. Several makers approve renewable diesel up to 100% in the same engines they limit to low biodiesel blends:

Maker / enginesRenewable dieselBiodieselSource
DetroitUp to 100%B5 for most B20 only for 2024+ CARB-certified DD engines and 2004+ Series 60; nothing above B20Detroit Fuels Brochure BRO-120, Jan. 2025
Volvo D13 (2027)R100Up to B20FreightWaves, May 2026
John Deere Tier 4RD100B30 since Aug. 2025, up from B20; Tier 3 and older up to B100American Soybean Association, Nov. 2025
CumminsGensets: HVO Entire diesel genset line, standby, EN 15940 fuelsB7 all; B20 listed BQ-9000 supplier and new filters requiredCummins, Dec. 2021; Service Bulletin 3379001
CaterpillarGensets: HVO All Cat generator sets, EN 15940 or D975, standby and primeMost nonroad up to B20 Not recommended for standby powerCat renewable liquid fuels FAQ; SEBU6250-21

Approvals change by model year, certification and duty rating. Use this as a starting point and check the fuel section of each engine's manual or the maker's current bulletin. The full B20 table by maker is in can my engine run B20?; generator approvals are in renewable diesel for data center generators.

What this means for a mixed fleet. With biodiesel, the lowest approval in the fleet sets the blend for a shared tank: one B5-only engine and the whole tank is B5. Renewable diesel removes that ceiling. Older seals are the one thing to watch. Neste says renewable diesel's lack of aromatics can shrink elastomers already swollen by aromatic or biodiesel-containing fuel, especially very old ones, and that leaks are probable where nitrile seals sat in a high biodiesel blend that is then taken away. Check older units for weeps after the first fills.

Cold weather

Cold flow: which one gels first

Biodiesel is the weaker of the two in the cold. Clean Fuels Alliance America says B5 clouds at about the same temperature as its #2 base and B20 about 2–7°F higher. NREL puts B100's cloud point at 27°F to 61°F depending on feedstock, and says cold-flow additives are believed to work only on the diesel portion of a blend. EIA lists better cold performance among the reasons renewable diesel took market share from biodiesel.

Renewable diesel's cold flow is a product choice. NREL says it can be made to meet a range of cloud point requirements, and producers sell summer and winter grades. Two things work differently than with diesel: Neste says its cold filter plugging point sits close to its cloud point, and cold-flow additives give only minor improvement. So the fix is ordering the right seasonal grade, not adding more additive. Ask for the cloud point of what's being delivered.

Cloud and gel points for #2, #1, B20, B100 and R99 side by side are in what temp does diesel gel?, and blend and additive tactics are in how to prevent diesel gelling.

Storage

Storage stability, water and microbes

For a tank that turns over every week, either fuel is fine. For fuel that sits, the chemistry matters.

Renewable diesel

Stable, but not immune

  • No use-before date. Neste says its stability is at the level of conventional diesel and names emergency generators among suitable uses.
  • Less water. Neste says it picks up and dissolves water even less than fossil diesel.
  • Microbes still grow at a fuel-water interface, so tanks need draining and sampling like any diesel tank.
Biodiesel blends

Plan for age, water and sludge

  • Up to a year. NREL expects B20 meeting spec to hold quality for up to a year in clean, dry storage.
  • More water. Caterpillar says biodiesel absorbs water more readily than diesel.
  • Solvency. It loosens old tank deposits; NREL recommends cleaning tanks before switching to B20 or higher.

Standby tanks are where the difference shows. Caterpillar's renewable fuels FAQ says biodiesel has a much shorter shelf life than diesel or HVO and is not recommended for standby power. That is why data centers and other standby sites look at renewable diesel rather than higher biodiesel blends. Whichever fuel is in the tank, the routine is the same: keep it dry, sample it, and see how long diesel lasts, water in diesel fuel and generator fuel quality testing. Tell the lab which fuel it is: Neste says the Rancimat oxidation test written for biodiesel isn't valid for renewable diesel.

Energy and combustion

Energy content, cetane and lubricity

Both fuels carry less energy per gallon than petroleum diesel. The DOE's fuel properties table puts the gap at about 4% for renewable diesel and 7% for B100:

FuelBtu/gal (lower heating value)vs ULSDCetane
ULSD #2128,488—40–55
Renewable diesel (RD100)123,710−3.7%70–85
B20≈126,700−1.4%—
Biodiesel (B100)119,550−7.0%45–65

DOE Alternative Fuels Data Center, Fuel Properties Comparison. B20 is calculated by volume share (80% ULSD, 20% B100); the DOE doesn't list it. Higher-heating-value figures in our biodiesel post give the same 1.4% for B20.

In practice, a gallon of R99 does about 4% less work than a gallon of ULSD, and a B20 blend about 1.4% less. Neat B100 is the outlier. For tank sizing and generator runtime, that's the number that matters: the runtime math is worked through in renewable diesel for generators, and you can price the difference in the fleet fueling cost calculator.

Cetane is where renewable diesel stands out: 70–85 against 40–55 for diesel, per the DOE. Lubricity goes the other way. NREL says 2% biodiesel almost always gives a blend enough lubricity to meet the D975 limit, while the DOE notes renewable diesel, like ULSD, needs a lubricity additive. Ask your supplier to confirm each load is treated.

Emissions

Carbon intensity and tailpipe emissions

Per gallon of neat fuel, the two are closer than most marketing suggests. The lifecycle numbers depend mostly on the feedstock:

  • Renewable diesel: the DOE says it cuts carbon intensity by 65% on average against petroleum diesel, based on California's Low Carbon Fuel Standard certified values.
  • Biodiesel: the DOE cites Argonne's analysis putting B100 at 74% lower than petroleum diesel, with similar values from the California Air Resources Board.
  • Same feedstock, both fuels: Argonne's 2022 study found 79–86% reductions for both fuels made from tallow, used cooking oil and distillers corn oil, and 40–69% from soybean, canola and carinata oil after land-use change.

Sources disagree on which process comes out ahead, and the gap is small either way. Argonne found the biodiesel route lower for crop oils, because transesterification uses less energy than hydroprocessing, but slightly higher for tallow. Neste, citing EU default values, says HVO comes out slightly lower than FAME from the same feedstock. What changes the total is the blend. B20 carries one fifth of B100's renewable fuel; R99 carries 99%. If the goal is a large cut in fuel-related emissions without new equipment, that's the practical difference.

Tailpipe. NREL says engines with modern emission controls show very little change in vehicle emissions whatever the fuel, and that biodiesel's effect on NOx in older, pre-2007 engines is still debated. The DOE reports an NREL study in which renewable diesel reduced NOx compared with petroleum diesel, and Neste's engine tests found NOx falling or unchanged on HVO while FAME typically raised it. Neither fuel makes a diesel engine emission-free at the stack.

How to report renewable diesel in a carbon inventory, and what paperwork to keep with each load, is covered in carbon reporting for renewable diesel.

Cost

What drives the cost of each

There's no fixed spread between the two. These are the factors that move it:

  • Feedstock. Both compete for the same fats and oils. EIA says soybean oil is the main U.S. biodiesel feedstock.
  • Process and scale. Hydroprocessing needs hydrogen and more energy, but renewable diesel plants are larger and can be converted refinery units (EIA, Argonne).
  • Federal RFS credits. EIA says biodiesel generates 1.5 renewable identification numbers (RINs) per gallon and renewable diesel 1.6 to 1.7. With biomass-based diesel RINs at $2.41 on June 4, 2026, EIA put the credits at more than $3.50 a gallon. More RINs per gallon is one reason EIA gives for renewable diesel overtaking biodiesel.
  • State clean fuel programs. California, Oregon and Washington reward low-carbon fuels, which is why renewable diesel concentrates there (EIA).
  • Federal tax credit. The $1-a-gallon blender's credit ended after 2024. Its replacement, the section 45Z clean fuel production credit, applies only to fuel produced in the U.S. (EIA), goes to registered producers, and runs through 2029 under Public Law 119-21. EIA says the change cut biodiesel and renewable diesel imports sharply in the first half of 2025. Detail is in our biodiesel post.
  • Freight. Distance from supply. That matters more for renewable diesel, which is made in few places (see supply).

Dated price points, for scale only. In the DOE Clean Cities price report for July 2026, B20 averaged $4.76 a gallon at retail against $4.86 for diesel nationally. Renewable diesel prices came almost entirely from California, where it averaged $6.42 against $6.38 for diesel. Only three renewable diesel prices were reported from outside California. These are voluntary pump-price surveys including taxes, not delivered bulk prices. Current diesel benchmarks are in the diesel price report.

Not price, tax or legal advice

Prices here are dated survey averages, not quotes or forecasts. RIN values, state credit values and federal tax credit rules change, and the credits described are earned upstream by producers, importers and blenders, not claimed by a fleet buying finished fuel. Check current rules with a tax professional.

Availability

Availability by region

Biodiesel is made all over the country in small plants. Renewable diesel is made in a few very large ones and shipped to the states that pay for it.

EIA capacity dataRenewable diesel and other biofuelsBiodiesel
Jan. 1, 2026 (released Sept. 2026)19 plants, 324,000 b/d45 plants, 128,000 b/d
Jan. 1, 2025 total19 plants, 4,719 million gal/yr48 plants, 1,986 million gal/yr
Where (Jan. 1, 2025)Gulf Coast 2,129 and West Coast 1,799 million gal/yr; Midwest 398Midwest 28 plants, 1,419 million gal/yr (about 71%)

EIA, U.S. Renewable Diesel Fuel and Other Biofuels Plant Production Capacity (Sept. 2025) and U.S. Biofuels / Biodiesel Plant Production Capacity (Sept. 2025 and Sept. 2026). EIA's renewable category also includes renewable jet fuel, naphtha and co-processing refineries.

  • West Coast: EIA reported renewable diesel at nearly 65% of California's transportation distillate in the third quarter of 2024, and more than 15% in Washington in the second quarter. In Oregon, biofuels were about a quarter, with renewable diesel about twice biodiesel's share.
  • East Coast: EIA said no renewable diesel is produced there. Record months in 2024 reached 5,000–7,000 barrels a day, more than half imported, the rest by tanker or barge from the Gulf Coast.
  • Everywhere else: biodiesel can be in ordinary diesel at up to B5 without a label, and most biodiesel production capacity sits in the Midwest.

Nationally, EIA says renewable diesel consumption passed biodiesel in January 2022. Away from the West Coast, though, renewable diesel is a fuel you plan for: confirm the supply route and lead time before you commit a fleet or a site to it, and agree what goes in the tank if a load is late.

Choosing

Which one fits your operation

Lean renewable diesel

When fuel sits, gets cold or must cut carbon

  • Standby generators and tanks that turn over slowly
  • Mixed fleets where one engine caps biodiesel at B5
  • Cold-weather work, with the right seasonal grade
  • Emissions targets that need a high renewable share without new equipment
Biodiesel blends work

When tanks turn over and engines are approved

  • On-road fleets burning fuel weekly, with engines approved for the blend
  • Sites where renewable diesel would have to travel a long way
  • Operations that want some renewable content in ordinary diesel
  • Customer contracts or programs that name a biodiesel blend

Before you switch, in five steps

  1. List every engine and note its highest approved biodiesel blend and any renewable diesel approval.
  2. Check the tank. Sample it, and polish or draw down any tank holding more than about 7% biodiesel before the first R99 load.
  3. Set the winter grade and ask for its cloud point before the first cold month.
  4. Recalculate runtime and range for about 4% more gallons on R99, or about 1.4% on B20.
  5. Agree the paperwork: product, blend level, spec and any carbon intensity basis with each delivery.
FuelGo

R99 or a biodiesel blend, delivered

FuelGo delivers R99 renewable diesel nationwide as a drop-in replacement for petroleum diesel, with sustainability documentation for your ESG reporting. R99 isn't stocked at every terminal. Where we can pull it locally, it moves like any other load; where there's no local terminal, we bring it in by rail or barge, and dispatch confirms the supply route and lead time for your site before we quote.

Our on-road diesel comes in B0, standard B5 or enhanced B10, with higher biodiesel blends on request, and the blend is quoted as a separate line. Switching fuels? Lab fuel testing checks what's in the tank, and fuel polishing and tank cleaning deal with what it finds. That's 20 to 4,400 gallons per drop and transport loads up to 7,500 gallons, into site tanks, generators or straight into trucks with mobile fleet fueling. Dispatch runs 24/7/365. Get a delivered quote or call 800-720-4546; a dispatcher replies within the hour.

Common questions

Renewable diesel vs biodiesel FAQ

What is the difference between renewable diesel and biodiesel?
Both are made from fats and oils, but the process is different. Renewable diesel is hydrotreated into hydrocarbons that meet ASTM D975, the same spec as petroleum diesel, so it can be used neat as R99 or R100. Biodiesel is made by transesterification into fatty acid methyl esters (FAME), meets ASTM D6751 as B100, and is sold in blends with petroleum diesel.
Is renewable diesel better than biodiesel?
For storage, cold weather and engine approvals, renewable diesel usually has the edge: it meets the diesel spec at any ratio, has no use-before date per Neste, and engine makers such as Detroit approve it up to 100% while capping biodiesel at B5 or B20. Biodiesel is made in more places, can be in ordinary diesel at up to B5, and adds lubricity. Lifecycle carbon depends mostly on the feedstock, not the process.
Can you mix renewable diesel and biodiesel in the same tank?
In small amounts. Neste advises against storing renewable diesel with more than 7% biodiesel, because impurities in the biodiesel can drop out of the low-aromatic fuel and plug filters. If a tank held B20, draw it down or polish it before switching to R99, and tell your fuel lab which product is in the tank.
Is renewable diesel a drop-in replacement for diesel?
Yes. EIA and the DOE Alternative Fuels Data Center both say renewable diesel meets ASTM D975 and can be used in existing diesel engines and infrastructure, blended with petroleum diesel in any amount. Still check your engine maker's fuel bulletin: Detroit, John Deere (Tier 4) and the 2027 Volvo D13 approve it up to 100%, and Cummins and Caterpillar have published generator set approvals.
Which gels first, biodiesel or renewable diesel?
Usually biodiesel blends. Clean Fuels Alliance America says B20 clouds about 2–7°F above the #2 diesel it is blended into, and NREL puts B100's cloud point at 27°F to 61°F. Renewable diesel's cloud point is set by the producer and season, cold-flow additives help it only a little according to Neste, so ask for the cloud point of the winter grade.
Which has lower carbon emissions, renewable diesel or biodiesel?
Per gallon of neat fuel they are close, and the feedstock matters more than the process. The DOE says renewable diesel averages 65% lower carbon intensity than petroleum diesel based on California certified values, and Argonne puts B100 at 74% lower. A 2022 Argonne study found 79–86% reductions for both fuels made from waste fats and 40–69% from crop oils. A B20 blend carries only a fifth of that renewable fuel.
Why is renewable diesel hard to find outside California?
Because California, Oregon and Washington have clean fuel programs that reward it, so that is where most of it goes. EIA reported that renewable diesel made up nearly 65% of California's transportation distillate in the third quarter of 2024, while the East Coast received only 5,000–7,000 barrels a day at record months in 2024, with none produced there.
Is renewable diesel or biodiesel better for a standby generator tank?
Renewable diesel, in most cases. Neste says its renewable diesel needs no use-before date and lists emergency generators among suitable uses, and Caterpillar says biodiesel has a much shorter shelf life and is not recommended for standby power. Either fuel still needs a dry tank and regular sampling, because microbes grow where water collects.

Sources: DOE AFDC, Renewable diesel (hydrotreating; meets D975 and EN 15940, not EN 590 density; 65% average lower carbon intensity from California LCFS certified values; NOx; nearly all used in California) · DOE AFDC, Fuel Properties Comparison (chemistry, cetane, Btu per gallon, lubricity) · DOE AFDC, Biodiesel vehicle emissions (Argonne B100 74% lower) · EIA, Biofuels explained: biodiesel and renewable diesel (processes, D975/D6751, pipelines, soybean feedstock) · NREL/DOE, Biodiesel Handling and Use Guide, 6th ed. (renewable diesel vs biodiesel; cloud point; B20 storage; lubricity; blend levels; tailpipe emissions; straight vegetable oil) · Neste Renewable Diesel Handbook (May 2016) (process; storage and water; FAME 7% limit; cold flow; seals; NOx; Rancimat; RED lifecycle comparison) · Xu et al., Life Cycle Greenhouse Gas Emissions of Biodiesel and Renewable Diesel Production in the United States, Environ. Sci. Technol. 2022 (Argonne) · Clean Fuels Alliance America, Cold Flow fact sheet · Detroit Fuels Brochure, Renewable Diesel Fuel · Detroit Fuels Brochure BRO-120, Engine Compatibility · FreightWaves, Inside Volvo's new D13 engine for 2027 (May 2026) · American Soybean Association, John Deere announces B30 compatibility (Nov. 2025) · KHL, Cummins generator sets approved for HVO (Dec. 2021) · Cummins Service Bulletin 3379001, Fuels for Cummins Engines · Caterpillar, Renewable Liquid Fuels: 3500 and C175 Generator Sets FAQ · Caterpillar, Machine Fluids Recommendations SEBU6250-21 · EIA, Biofuels displacing petroleum distillate on the West Coast (July 2023) (renewable diesel passed biodiesel in Jan. 2022, and why) · EIA, Higher blending targets drive RIN prices (June 2026) · EIA, Biodiesel and renewable diesel imports fall in 2025 after tax credit change (Sept. 2025) · IRS, Instructions for Form 7218, Clean Fuel Production Credit · EIA, Renewable diesel on the U.S. West Coast (Feb. 2025) · EIA, East Coast renewable diesel (Dec. 2024) · EIA, U.S. Biofuels Plant Production Capacity (Sept. 2026) · EIA, Renewable Diesel Fuel and Other Biofuels Plant Production Capacity (Sept. 2025) · EIA, U.S. Biodiesel Plant Production Capacity (Sept. 2025) · DOE, Clean Cities and Communities Alternative Fuel Price Report (July 2026)