Skip to content
Data Center Fuel Quality

Data Center Generator Fuel Quality: Sampling, Testing, Polishing and Turnover

The tank will outlive the fuel in it. Generators that run a few hours a year never turn over a multi-day tank, so fuel quality has to be run as a program: sample, test, trend, polish, replace.

1×/yrFull lab panel, minimum
0.05%D975 max water & sediment
<3 hMicrosoft generator run per year
16+ yrsTo burn one 48-hour tank
Lab fuel testing
Polishing & tank cleaning
24/7/365 dispatch
800-720-4546
Quick Answer

A data center fuel quality program samples every generator tank from the bottom on a schedule and sends it to a lab. Run a full panel at least yearly and water and microbial checks more often. Trend each tank against its delivery baseline, polish when water, sediment or microbes rise, and replace fuel that has started to degrade.

Two technicians checking server racks in a data center aisle
The servers depend on generator fuel that may sit in the tank for years. Regular lab sampling is how you know it will still run the generators in an outage.
The problem

Why data center fuel quality is a turnover problem

Data center generators barely run. Microsoft's public datacenter fact sheet says its sites store enough fuel to run the generators for up to 48 hours, and that the generators run less than three hours a year at full or partial load, only to prove they work. Burning at most 3 of 48 hours a year, a tank uses about 6% of its fuel annually. At that rate it takes more than 16 years to burn through one fill.

Diesel doesn't last that long on its own. BP's storage bulletin gives 12 months or longer at about 68°F and 6 to 12 months where the tank sits above 86°F, and suggests planning to use stored fuel within 1 to 5 years. Bell Performance, which sells fuel additives, puts untreated backup fuel at 6 to 12 months and 2 to 3 years with a stabilizer and quarterly monitoring. The figures differ, but none of them come close to the time a data center tank actually holds its fuel. ASTM D975 calls anything over 12 months after the user receives the fuel long-term storage, and nearly every generator tank qualifies. More on the chemistry in how long diesel lasts.

Tank holds (hours at design load)3 run-hours a year12 run-hours a year24 run-hours a year
24 hours8 years2 years1 year
48 hours16 years4 years2 years
72 hours24 years6 years3 years

Years to burn through one tank = tank hours ÷ run-hours a year, counting run-hours at design load. Exercise runs at light load burn fewer gallons an hour, so real turnover is slower still. Tank sizing math is in how much diesel a data center needs.

So test runs alone won't keep the fuel fresh. The program has to find problems early, fix the fuel you can save and replace the fuel you can't.

The program

A data center fuel quality program in five parts

  1. Baseline every delivery. ASTM D975 sets the properties diesel must have at the time and place of delivery. Keep the paperwork (grade, dyed or clear, biodiesel content) and a retained sample of the load. That's the baseline every later test is measured against.
  2. Sample on a schedule. Bottom and all-level samples from each tank, on the calendar below, plus event-driven samples.
  3. Test at a lab and trend. The same panel, at the same lab, from the same sampling point, so a change means the fuel changed.
  4. Act on triggers. Drain, polish, treat, clean or replace, decided by the results, not by a symptom on the day of an outage.
  5. Record by tank. Results, deliveries, polishing and treatments logged against each sub-base, day and bulk tank.
Schedule

Data center fuel sampling schedule

No single schedule is published for every site, and sources set different intervals. Where NFPA 110 applies, it sets a floor: a fuel quality test at least once a year using appropriate ASTM standards (section 8.3.7 in the 2019 edition). Bell Performance recommends a full ASTM panel yearly, microbial monitoring quarterly and a monthly visual check. BP says to drain water weekly, and at least monthly if a tank shows no tendency to collect it. Put together, a schedule looks like this:

WhenWhatWhy
Every deliveryCheck the delivery paperwork for grade and blend, keep a retained sample, and look for clear and bright fuelD975 applies at delivery. The retained sample is the baseline, and it settles questions about where a problem came from.
MonthlyCheck for and drain bottom water; look at a bottom sample; check vents, fill caps and sealsWater is where microbes grow and corrosion starts. D975 says tanks should be set up for scheduled water draining.
QuarterlyMicrobial screen (ATP, ASTM D7687) and water on a bottom sampleCatches growth at the fuel-water interface before filters plug.
YearlyFull lab panel on bottom and all-level samplesStability, particulates, cloud point and spec properties, trended year over year.
Before winterCloud point (ASTM D2500)Fuel bought in summer can sit into January. See what temperature diesel gels.
After an eventRetest after an outage refill, a flood or rain intrusion, polishing or biocide treatment, or filters plugging earlyD975 warns that fuels from different sources can interact and end up less stable than either fuel alone.

Treat these as starting intervals. Hot sites, biodiesel blends, tanks with a history of water and any tank whose results start to move deserve shorter ones.

Sampling

Where to pull the sample

From the bottom. Water, sludge and degradation products settle in a still tank. ASTM D975 says to include a "bottom" or "clearance" sample, as defined in ASTM D4057, along with an "all level" sample. It also warns that samples drawn more than a foot or two above the bottom of a static tank will almost always look very clean. Bell Performance says labs generally recommend sampling three to six inches off the tank bottom.

  • Every tank separately. Sub-base, day and bulk tanks each get their own sample and their own record. A clean bulk tank says nothing about the belly tank under generator 7.
  • Same point, same method, every time. Otherwise a change in results may be a change in sampling.
  • Clean containers from the lab. Microbial samples especially need clean bottles and prompt shipping. Ask the lab for its containers and hold times.
  • Label everything. Tank ID, date, sampling point and the date of the last delivery.
Lab tests

Data center diesel fuel testing: D975, D6469 and the panel

ASTM D975 is the yardstick. It's the standard specification for diesel fuel, covering seven grades, and stationary generators typically burn Grade No. 2-D S15 (ultra-low sulfur). It prescribes properties at the time and place of delivery. Its storage guidance (Appendix X3) is a set of suggested practices, and its appendix on microbes says no microbial quality criterion for fuel is recommended.

ASTM D6469 is a guide, not a test. The Standard Guide for Microbial Contamination in Fuels and Fuel Systems is written for people with a limited microbiology background: it explains symptoms, occurrence and consequences, and suggests ways to detect and control contamination. The tests themselves are separate methods:

TestMethodWhenHow to read it
Water & sedimentASTM D2709Quarterly, yearlyD975 maximum is 0.05% by volume. A rising number means water is getting in.
Water contentASTM D6304 (Karl Fischer)YearlyTotal water in ppm, including dissolved water you can't see. Trend it.
AppearanceASTM D4176Every sampleClear and bright, or hazy with free water and particles.
Microbial activityASTM D7687 (cellular ATP)QuarterlyAbout 5 minutes per test, against 36 to 48 hours or more for culture methods. D975 sets no limit, so use the lab's action levels and your own trend.
Oxidation stabilityASTM D7545; EN 15751 for B6–B20 blendsYearlyD975 says the older D2274 and D5304 tests were developed for higher-sulfur fuels and may not show instability in S15 fuel. D7545 has been shown to be suitable for it.
ParticulatesASTM D7321; D6217 only for fuel without biodieselYearlyInsoluble contaminants that load filters and wear injectors.
Cloud pointASTM D2500Before winterWhether the fuel in the tank suits the coldest weather ahead.
Flash point, sulfurASTM D93, D5453Yearly or after a suspect deliveryCatches the wrong product or a mixed load. For 2-D S15, D975 sets 52°C minimum flash and 15 ppm maximum sulfur.

Method details and what each test means for any stored diesel: testing stored diesel and contamination testing.

Trend, don't just pass or fail. D975 says performance criteria for accelerated stability tests that assure satisfactory long-term storage have not been established, and it sets no microbial limit. A single result rarely tells you much. The same tank tested the same way every quarter shows you which way the fuel is heading.

Triggers

What to do when results move

FindingAction
Free water, or water & sediment risingDrain the water, find the source (vents, fill caps, seals), then polish. Retest.
Microbial activity risingPolish, and treat with an EPA-registered biocide applied per its label. BP warns a kill dose leaves dead matter that can block filters, so follow it with polishing or draining. Retest to confirm.
Sludge or slime on the tank floor, or results that bounce back after polishingTank cleaning. Polishing cleans the fuel, not the tank walls.
Stability falling, fuel darkening or gums formingReplace it. D975 says even mildly to moderately degraded fuel isn't fit for modern fuel systems, and that drawing fuel off above the sediment doesn't remove dissolved polymers and aging acids.
Cloud point too high for the coming winterTreat or blend before the cold arrives. See how to prevent diesel gelling.
Flash point or sulfur off specIsolate the tank, pull the retained delivery sample and call the supplier.

What polishing can and can't fix, and when a tank needs cleaning instead, is covered in fuel polishing vs. tank cleaning.

Polishing

Polishing: built into the plant or brought to it

Uptime Institute notes that fuel treatment isn't required by Tier topology, but calls it an important Operational Sustainability characteristic: permanently installed treatment systems "encourage regular fuel maintenance and improve long-term availability." It asks designers to integrate them carefully so the Tier objective isn't compromised.

Where a built-in system isn't practical, as with existing sub-base tanks, edge sites or a few large tanks, a mobile polishing visit does the same job at the tank. Either way, schedule it from the test results and retest afterward, so the record shows the fuel came back into range.

Turnover

Turning over fuel that rarely gets used

D975's storage appendix calls a monitoring plan "an integral part of a successful fuel quality program" and adds that a plan to replace aged fuel with fresh product is also desirable. The levers:

Buy for storage

Tell the supplier it's long-term

D975 says long-term storage needs should be discussed with the supplier, and that stability additives work best at the refinery or within a few weeks of production. Ask what's in the load: D975 lets No. 2 diesel contain up to 5% biodiesel. See biodiesel vs. diesel.

Keep it full

Less air, less water

D975 says fixed-roof tanks should be kept full to limit oxygen and tank breathing. Top off after every test window, and keep copper, brass and galvanized fittings out of the fuel system.

Replace on a plan

Rotate before it fails

Set a replacement age or trigger for each tank. When results say the fuel is aging, pump it out and refill with fresh fuel on a schedule you pick, not after a failed load test.

Mixing loads

Watch the outage refill

After a long outage, tanks get fuel from whichever trucks arrive. D975 warns that blends from different sources can be less stable than expected, so retest once things settle. Renewable diesel is covered in R99 renewable diesel.

Roles

Who does what

WhoOwns
Facility / critical facilities teamThe program: schedule, monthly checks, water draining, records, and the call to polish, clean or replace.
Testing labMethods, sample containers, results and action levels.
Fuel supplierOn-spec deliveries with grade and blend documented, refills after tests, and replacement fuel.
Polishing contractor or built-in systemPolishing, tank cleaning, pump-out, and retesting after service.
Generator maker and engineer of recordThe engine's fuel requirements, filtration, and how treatment ties into the fuel system.

Colocation tenants who don't manage the tanks themselves should ask the operator for the testing schedule, the latest results by tank and the last polishing date. Generator-side maintenance is in the generator maintenance checklist and diesel generator maintenance tips.

FuelGo

Fuel quality on the same account as the fuel

FuelGo does lab fuel testing: we pull a sample from your tank and send it to a lab that checks it for water, sludge, bacteria and more. The results decide whether the fuel is fine, needs polishing, or needs pumping out and replacing. We polish on site for tanks from 50 to 50,000 gallons, clean tanks of sludge and water, and pump out fuel that can't be saved, then refill with dyed diesel, clear diesel or R99 renewable diesel on the same account.

A regular maintenance plan puts polishing visits on a set schedule alongside keep-full deliveries, with tank monitoring available. Fills are scheduled around your weekly or monthly generator tests, delivered at 20 to 4,400 gallons per drop and transport loads up to 7,500, and itemized by gallons, date and tank. Dispatch is staffed 24/7/365. See our data center fuel delivery page and the data center generator fuel guide. Get a free quote or call 800-720-4546; a dispatcher replies within the hour.

Common questions

Data center generator fuel quality FAQ

How often should data center generator fuel be tested?
There is no single industry schedule, and sources differ. A workable program checks for water and looks at a bottom sample monthly, runs a microbial and water screen quarterly, and sends a full lab panel at least once a year. Add tests before winter, after an outage refill and whenever filters start plugging early, and test more often if results start to move.
What tests should be in a data center fuel test panel?
Water and sediment (ASTM D2709), water content by Karl Fischer (D6304), appearance (D4176), microbial activity by ATP (D7687), oxidation stability, particulates and cloud point (D2500). Flash point and sulfur are worth adding once a year or after a suspect delivery. ASTM D975 notes that the older stability tests, D2274 and D5304, may not show instability in ultra-low sulfur diesel, while D7545 has been shown to be suitable for it.
Where should a generator fuel sample be taken?
From the bottom of the tank, where water, sludge and microbes settle, along with an all-level sample, as ASTM D975 recommends. D975 warns that samples drawn more than a foot or two above the bottom of a still tank almost always look clean. Sample each tank on its own, from the same point every time.
Is ASTM D975 the standard for stored generator fuel?
D975 is the specification for diesel fuel, and it prescribes the properties fuel must have at the time and place of delivery. It is the right yardstick for test results, but its storage guidance is an appendix of suggested practices. It sets no microbial limit and says no performance criteria for accelerated stability tests have been established, so trend each tank against its own baseline.
What is ASTM D6469?
ASTM D6469 is the Standard Guide for Microbial Contamination in Fuels and Fuel Systems. It is a guide rather than a test method: it explains the symptoms, occurrence and consequences of microbial contamination for readers with limited microbiology background, and suggests ways to detect and control it. The quarterly microbial screen in most programs uses a test method such as ASTM D7687.
How long can diesel sit in a data center generator tank?
Sources differ. BP's storage bulletin gives 12 months or longer at about 68°F and 6 to 12 months where it is regularly above 86°F, and suggests planning to use stored fuel within 1 to 5 years. A fuel additive maker puts untreated fuel at 6 to 12 months and 2 to 3 years with stabilizer and quarterly monitoring. Most data center tanks hold fuel far longer than that, which is why they need testing and polishing on a schedule.
When should stored fuel be polished, and when should it be replaced?
Polish when water, sediment or microbial results rise but the fuel itself is still sound. Replace it when stability results fall or the fuel has started to degrade: ASTM D975 says even mildly to moderately degraded fuel is not fit for modern fuel systems, and drawing fuel off above the sediment does not remove dissolved polymers and aging acids. Clean the tank when sludge or slime builds up faster than polishing removes it.
Who is responsible for generator fuel quality at a data center?
The facility team owns the program: the schedule, monthly checks, records and decisions. A lab runs the tests, the fuel supplier delivers on-spec fuel and refills, a polishing contractor or built-in system cleans the fuel, and the generator maker and engineer of record set the engine's fuel requirements. Colocation tenants should ask the operator for the testing schedule and the latest results.

Sources: ASTM D975-24, Standard Specification for Diesel Fuel, NCWM copy (1.1 grades; 1.2 properties at delivery; 3.2.2 long-term storage; Table 1 limits; 7.3.1.2 up to 5% biodiesel; X3.2–X3.8 storage, sampling, stability tests, degraded fuel; X6 microbial) · ASTM D6469, Standard Guide for Microbial Contamination in Fuels and Fuel Systems (scope) · ASTM D7687, cellular ATP in fuel (scope; about 5 minutes vs. 36–48 hours for culture) · Bell Performance, What NFPA 110 requires for stored generator fuel, Aug. 2026 (annual fuel quality test, 8.3.7 in the 2019 edition) · Bell Performance, Data center generator fuel quality, June 2026 (yearly panel, quarterly microbial, monthly visual; 3–6 inches off the bottom; 6–12 months untreated, 2–3 years managed) · BP Australia, Long term storage of diesel (storage life by temperature; 1–5 year turnover; water draining; biocide kill dose) · Uptime Institute Journal, Fuel System Design and Reliability (fuel treatment and Tier topology) · Microsoft, Datacenter fuel safety and sustainability fact sheet (up to 48 hours of fuel; under three hours a year of generator operation). The turnover table and the 6% and 16-year figures are FuelGo calculations from these sources.